September 9, 2020
eAssignment Store

AUR30616 – 17 – AURETR010 – Repair wiring and harnesses and looms, Electronics Assignment Help, Electrical Homework Help

  1. List 5OHS & WHS procedures to be followed while working on wiring harness.
  2. List 5OHS & WHS procedures to be followed while working on wiring harness.
  3. List 5OHS & WHS procedures to be followed while working on wiring harness.
  4. List 5OHS & WHS procedures to be followed while working on wiring harness.
  5. Describe the storage and disposal procedure for hazardous materials and toxic substances as per environmental requirements in about 40 – 70 words.
  6. What is meant by manufacturer specifications and where can it be located? (in about 30 – 50 words)
  7. Describe the following types of single wiring harness in about 50 – 70 words each.
  8. Explain the complex wire looms (in about 30 – 70 words).
  9. How does the thickness of wire gauge affect an electrical system? (in about 40 – 50 words).
  10. What is CAN Bus system? List 5 advantages of using a CAN-bus.
  11. Why is it not recommended to untwist the twisted pair in the CAN Bus wiring during repairs? Give 2 reasons.
  12. Why should all the wirings be shielded?(40-50 words)
  13. Identify the type of faults in the below given electrical components
  14. What are the common causes for the below-given faults in an electrical system? (30- 40 words each)
    – Component Damage and Wear
    – Component Corrosion
    – Water and Moisture Ingress
    – Damaged Insulation
    – Frayed Wires
    – Burnt Wires
    – Connector Damage
    – Terminal Damage
  15. Describe the visual testing procedures for electrical circuits and components in about 40-60 words.
  16. Describe the procedure for voltage drop test (in about 60 – 80 words).
  17. How can be the Electrical resistance tested? (in about 100 – 150 words)
  18. Explain briefly how electrical terminals can be accessed without damaging connectors and wires in about40 -60 words.
  19. Explain how the panels and covers are removed from wiring system? (in about 70 – 100 words)
  20. Describe the procedure for removing and replacing components with wiring looms (in about 80 to 110 words).
  21. Explain briefly the procedure to remove connector terminal pins in about 50 – 70 words.
  22. Explain the process of terminal crimping in about 100 – 130 words.
  23. Describe the procedure for soldering electrical wire connections (in 130 – 170 words).
  24. Explain the procedure to remove and replace connectors including male and female connectors (in about 120 – 140 words).
  25. Briefly describe the harness and loom protections in about 50 – 70 words.
  26. How can you identify the cable size and terminal type with the help of current drawn? (in about 40 – 70 words)
  27. List 5 post repair testing procedures of wiring harness and looms.

Team Codingparks

Thanks for reading about a team of super programmers cum developers. Not even this, a Digital Marketing Experts team too. Yes, you heard it right! Get your development and marketing solution both from us. I can make your to reach the hight what it is meant to be.

Related Posts

SYST13416 – Linux Assignment Help

Your assignment will be working with the phonebook file. Out of country students without access to Atlas will need to install Ubuntu or other …
Employability Skills Business Project

Employability Skills Business Project

Module: Employability Skills Business ProjectTutor: Nathan VeerasamyAssessment type: Individual Business Project Report WRIT1 (100% weighting) Aims: Enable students to develop a greater understanding of …

Give a Comment